Samsung’s HDD Installation Guide: A Natural Opportunity for a Cartoon Caption Contest
September 14, 2011
Seagate ST3750330AS 750 GB
September 20, 2011

A read/write head is the business end of a hard drive. It’s the hitch of a trailer, the edge of a knife, the nib of a pen, the glove of an outfielder. It’s the interface of separate parts. It’s where the action happens.

When it reads data, it floats within a few nanometers of a spinning platter. Tiny magnetic differences on the surface of the platter — basically on or off signals — induce electrical pulses in the head, which become the stream of 1s and 0s that the right software will turn into the movie “Zoolander,” or whatever you happen to have on your hard drive.

When it writes data, electric signals flow through the head and magnetize a series of points on the platter.  We sometimes compare the read/write heads to needles on record players, but a needle — or stylus — is only a one-way translator. A needle sits in a groove and vibrates in response to the wave-like shapes that were cut into the groove. It doesn’t write anything onto a record, and the action is mechanical, rather than electrical.

In terms of what’s going on inside, the hard drive’s read/write head is actually closer to what was found in cassette players. A chief difference is scale. Hard drives now have read/write heads that need magnification to see. They float on winglike arms that carry the heads on a cushion of air so thin that you can measure it by the number of oxygen or nitrogen molecules between the head and the platter.

As you might guess, these read/write heads are highly specialized, and each drive typically has several of them — usually one per platter surface, top and bottom, if storage space is to be maximized.

When a read/write head fails, it’s big trouble. All of a sudden, the data on your hard drive is inaccessible. And worse, there’s a risk that a failed head could make contact with the platter. This is bad because any collision with the platter will likely scrape off the magnetized material that holds all those magnetic sign. These scratches — called rotational scoringusually rule out successful data recovery because they have turned what was once data on a platter into dust.

We routinely replace damaged read/write heads as part of our cleanroom data recoveries, and it’s a delicate operation. To perform it properly, we’ve developed proprietary data recovery tools and a vast library of compatible hard drive parts.

The recovery of a failed read/write head on a Seagate Barracuda 750 GB SATA hard drive depended on a successful replacement of a head before we could recover the data. The effort was successful, and we were able to retrieve the data for Mainsail Printing & Graphics, an excellent graphic design and print shop in Savannah, Georgia.

Our client there, Rob King, writes:

I am a graphic designer and Gillware saved my business. I just received my hard drive from Gillware and it is flawless! 100% of my data was recovered. The price was half of what others wanted and the turnaround was faster too!

My business relies on this data, so waiting a month was simply not an option. The entire process with Gillware took just over 1 business week, which includes shipping, and was very much worth the price. Thanks again, guys. You rock!


14 Comments

  1. […] the original: Anatomy of a read/write head failure | Gillware Online Backup and … © 2011 Data Recovery […]

  2. […] Anatomy of a read/write head failure | Gillware Online Backup and … Tags: called-rotational, data-recovery, once-data, recovery, routinely-replace, rule-out, […]

  3. […] a successful replacement of one of the read/write heads we were able to recover all of the data that Mainsail Printing & Graphics in Savannah, Georgia […]

  4. […] certain situations, the read/write heads can crash and contact the delicate platter surface. Since the heads are so close to the platters, even a tiny […]

  5. […] you may have guessed, the read/write heads are a common failure point in hard drives. They are one of the hardest working components inside a hard drive and also one of […]

  6. […] Damage to the HDD platters presents two distinct challenges to data recovery labs. One of these challenges is the destruction of the data that lives in the regions of the disk that are physically scratched or damaged. Unfortunately, nothing can be done to remedy this. The data in those areas has been scratched from the platter surface and is not recoverable. But what about all the areas of the platter(s) that are not physically damaged? Surely something can be done to recover the data in the areas of the platter that have not been relegated to a life as a pesky dust particle. The short answer is yes, but doing so means we need to overcome the second challenge that data recovery labs face when attempting to recover data from an HDD with platter damage: dust. Not dust like you find on those annoying blinds you keep forgetting to wipe down during your spring cleaning kick, but rather the ultra-hard microscopic particulates generated inside the HDD when the read/write heads contact the platter surface. These particulates embed themselves in the platter surface and can damage otherwise healthy read/write heads. […]

  7. […] you may have guessed, the read/write heads are a common failure point in hard drives. They are one of the hardest working components inside a hard drive and also one of […]

  8. […] article that you have been researching, writing and editing for months is suddenly buried within a clicking hard drive and a laptop computer that shows only a blue […]

  9. […] my hard drive. Fortunately, there was nothing physically wrong with the drive, which could have made recovery […]

  10. […] certain situations, the read/write heads can crash and contact the delicate platter surface. Since the heads are so close to the platters, even a tiny […]

  11. […] Hard drive performance decreases with age, especially as the drive fills up and the data on it becomes more spread out across the disks. The more data you have, and the more spread-out it is, the harder your read/write heads have to work and the longer they have to search to find it. Not only does this lead to increased latency and seek times, but it also puts increased stress on your read/write heads. The headstack is already the most delicate of your hard drive’s internal components. […]

  12. […] you may have guessed, the read/write heads are a common failure point in hard drives. They are one of the hardest working components inside a hard drive and also one of […]

  13. […] However, in certain situations the heads can “crash” and contact the delicate platter surface, damaging the layer of substrate and spreading microscopic debris throughout the chassis. Though this damage may seem minor, the debris continually impacts the read/write heads, eventually destroying them and rendering the drive inoperable. […]

  14. […] lab, data recovery engineers performed a full assessment and discovered the drive’s read/write heads had gotten stuck on the platters, preventing them from spinning. When the drive was dropped, it […]

Leave a Reply

Your email address will not be published. Required fields are marked *